Freematics Forum

Posted: **Wed Oct 27, 2021 6:53 am**

Hey,

I purchased 2 x Freematics ONE+ Traccar Edition

After doing the Freematics Builder configuration according to the guide. (both trackers were configured the same, same place, same PC and same sim providers "hologram") Yesterday two trackers were also tested on the road on two vehicles, and results follow;

First Tracker: Was connecting to the sim network & server, but when connected to OBD, the coordinates were showing Latitude 0.000000°, Longitude 0.000000°forwhole road trip.

SecondTracker: Wasn't connecting to server and sim provider.

: freematics-screenshot.PNG (49.71 KiB) Viewed 12180 times

Below are the outputs from the Freematics Builder console

First Tracker

E (202) spiram: SPI RAM not initi +K 5
E (202) esp_himem: Cannot allocate memory for meta info. Not initializing!
CPU:160MHz FLASH:4MB
IRAM:359KB
DEVICE ID:E5910RGP
TYPE:16
MEMS:ICM-20948
ACC BIAS:0.01/-0.02/-1.02
GNSS:NO
CELL:SIM7600E-H
IMEI:860147050686862
OBD:NO
SD:29832 MB total, 0 MB used
/DATA/1.CSV
/DATA/2.CSV
/DATA/3.CSV
/DATA/4.CSV
/DATA/5.CSV
/DATA/6.CSV
/DATA/7.CSV
File: /DATA/8.CSV
[BUF] 3 samples | 26 bytes | 3%
Operator:Optus AU Hologram
[BUF] 11 samples | 98 bytes | 12%
IP:100.66.160.120
RSSI:-95dBm
LOGIN(track.egemeats.com.au:5170)...
[BUF] 20 samples | 176 bytes | 21%
[BUF] 29 samples | 254 bytes | 31%
[BUF] 37 samples | 326 bytes | 40%
Server timeout
LOGIN(track.egemeats.com.au:5170)...
[BUF] 45 samples | 398 bytes | 50%
[BUF] 54 samples | 476 bytes | 59%
[BUF] 63 samples | 554 bytes | 68%
[BUF] 72 samples | 632 bytes | 78%

Unable to connect
[BUF] 81 samples | 710 bytes | 87%
LOGIN(track.egemeats.com.au:5170)...
[BUF] 90 samples | 788 bytes | 96%
[BUF] 92 samples | 808 bytes | 100%
[FILE] 1KB
[BUF] 93 samples | 814 bytes | 100%
[BUF] 93 samples | 814 bytes | 100%

Unable to connect
[BUF] 93 samples | 814 bytes | 100%
LOGIN(track.egemeats.com.au:5170)...
[BUF] 92 samples | 808 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%

Unable to connect
LOGIN(track.egemeats.com.au:5170)...
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%

Second tracker

CPU:160MHz FLASH:4MB
IRAM:359KB
DEVICE ID:E591GAG4
TYPE:16
MEMS:ICM-20948
ACC BIAS:1.00/-0.02/-0.06
GNSS:NO
CELL:SIM7600E-H
IMEI:860147050679503
OBD:NO
SD:29832 MB total, 1 MB used
/DATA/1.CSV
/DATA/2.CSV
/DATA/3.CSV
/DATA/4.CSV
/DATA/5.CSV
/DATA/6.CSV
/DATA/7.CSV
/DATA/8.CSV
/DATA/9.CSV
/DATA/10.CSV
/DATA/11.CSV
/DATA/12.CSV
/DATA/13.CSV
/DATA/14.CSV
/DATA/15.CSV
/DATA/16.CSV
/DATA/17.CSV
/DATA/18.CSV
/DATA/19.CSV
/DATA/20.CSV
/DATA/21.CSV
/DATA/22.CSV
/DATA/23.CSV
/DATA/24.CSV
File: /DATA/25.CSV
[BUF] 3 samples | 26 bytes | 3%
[BUF] 12 samples | 104 bytes | 12%
[BUF] 21 samples | 182 bytes | 21%
[BUF] 29 samples | 254 bytes | 31%
[BUF] 38 samples | 332 bytes | 40%
[BUF] 47 samples | 410 bytes | 50%
[BUF] 55 samples | 482 bytes | 59%
[BUF] 63 samples | 554 bytes | 68%
[BUF] 72 samples | 632 bytes | 78%
[BUF] 81 samples | 710 bytes | 87%
NO SERVICE,Online
[BUF] 89 samples | 782 bytes | 96%
CELL OFF
[BUF] 92 samples | 808 bytes | 100%
[FILE] 1KB
[BUF] 92 samples | 808 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
CELL:SIM7600E-H
IMEI:860147050679503
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
NO SERVICE,Online
[BUF] 92 samples | 808 bytes | 100%
CELL OFF
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
CELL:SIM7600E-H
IMEI:860147050679503

Posted: **Thu Oct 28, 2021 12:09 am**

Did you connect GPS receiver as I see you have model A and no GNSS is detected. Try powering from OBD instead of USB alone which might not supply sufficient power surge.

Posted: **Thu Oct 28, 2021 5:33 am**

I did connect the external GNSS.

Both connections have been tried (from OBD and USB Hub)

Posted: **Thu Oct 28, 2021 10:26 am**

If you see GNSS:NO there is no chance any coordinates will be obtained. GNSS receivers are not detected for some reason. Have you tried both receivers?
As for the cellular network issue, did you test with the same SIM card that works in another unit?

Posted: **Thu Oct 28, 2021 10:28 am**

Let me swap the sim cards and receivers. I will let you know, in 20 minutes

Posted: **Thu Oct 28, 2021 10:37 am**

stanley wrote: ↑Thu Oct 28, 2021 10:26 am If you see GNSS:NO there is no chance any coordinates will be obtained. GNSS receivers are not detected for some reason. Have you tried both receivers?
As for the cellular network issue, did you test with the same SIM card that works in another unit?

Done a test on the 2. device

E (202) spiram: SPI RAM not initi +K 5
E (202) esp_himem: Cannot allocate memory for meta info. Not initializing!
CPU:160MHz FLASH:4MB
IRAM:359KB
DEVICE ID:E591GAG4
TYPE:16
MEMS:ICM-20948
ACC BIAS:0.03/-0.01/0.99
GNSS:NO
OBD:NO
SD:29832 MB total, 1 MB used
/DATA/1.CSV
/DATA/2.CSV
/DATA/3.CSV
/DATA/4.CSV
/DATA/5.CSV
/DATA/6.CSV
/DATA/7.CSV
/DATA/8.CSV
/DATA/9.CSV
/DATA/10.CSV
/DATA/11.CSV
/DATA/12.CSV
/DATA/13.CSV
/DATA/14.CSV
/DATA/15.CSV
/DATA/16.CSV
/DATA/17.CSV
/DATA/18.CSV
/DATA/19.CSV
/DATA/20.CSV
/DATA/21.CSV
/DATA/22.CSV
/DATA/23.CSV
/DATA/24.CSV
/DATA/25.CSV
/DATA/26.CSV
/DATA/27.CSV
File: /DATA/28.CSV
[BUF] 3 samples | 26 bytes | 3%
[BUF] 11 samples | 98 bytes | 12%
[BUF] 20 samples | 176 bytes | 21%
CELL:SIM7600E-H
IMEI:860147050679503
[BUF] 29 samples | 254 bytes | 31%
[BUF] 38 samples | 332 bytes | 40%
[BUF] 47 samples | 410 bytes | 50%
[BUF] 56 samples | 488 bytes | 59%
[BUF] 65 samples | 566 bytes | 68%
[BUF] 72 samples | 632 bytes | 78%
[BUF] 81 samples | 710 bytes | 87%
[BUF] 90 samples | 788 bytes | 96%
[FILE] 1KB
[BUF] 93 samples | 814 bytes | 100%
[BUF] 93 samples | 814 bytes | 100%
[BUF] 93 samples | 814 bytes | 100%
CELL OFF
[BUF] 93 samples | 814 bytes | 100%
[BUF] 93 samples | 814 bytes | 100%
[BUF] 93 samples | 814 bytes | 100%
[BUF] 93 samples | 814 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
CELL:SIM7600E-H
IMEI:860147050679503
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
CELL OFF
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 92 samples | 808 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[FILE] 2KB
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
CELL:SIM7600E-H
IMEI:860147050679503
[BUF] 90 samples | 796 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
[BUF] 91 samples | 802 bytes | 100%
Stationary for 180 secs
STANDBY
ACC BIAS:-0.01/-0.01/0.99
CELL OFF

Posted: **Thu Oct 28, 2021 10:42 am**

Done a test on the 1. device

CPU:160MHz FLASH:4MB
IRAM:359KB
DEVICE ID:E5910RGP
TYPE:16
MEMS:ICM-20948
ACC BIAS:0.00/-0.25/-0.99
GNSS:NO
CELL:SIM7600E-H
IMEI:860147050686862
OBD:NO
SD:29832 MB total, 0 MB used
/DATA/1.CSV
/DATA/2.CSV
/DATA/3.CSV
/DATA/4.CSV
/DATA/5.CSV
/DATA/6.CSV
/DATA/7.CSV
/DATA/8.CSV
/DATA/9.CSV
/DATA/10.CSV
/DATA/11.CSV
/DATA/12.CSV
File: /DATA/13.CSV
[BUF] 3 samples | 26 bytes | 3%
[BUF] 11 samples | 98 bytes | 12%
[BUF] 19 samples | 170 bytes | 21%
[BUF] 28 samples | 248 bytes | 31%
[BUF] 37 samples | 326 bytes | 40%
[BUF] 45 samples | 398 bytes | 50%
[BUF] 54 samples | 476 bytes | 59%
[BUF] 63 samples | 554 bytes | 68%
[BUF] 72 samples | 632 bytes | 78%
[BUF] 80 samples | 704 bytes | 87%
NO SERVICE,Online
[BUF] 88 samples | 776 bytes | 96%
CELL OFF
[BUF] 90 samples | 796 bytes | 100%
[FILE] 1KB
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%
[BUF] 90 samples | 796 bytes | 100%

Posted: **Thu Oct 28, 2021 10:43 am**

tests were done on my desk, let me try it on OBD.

Posted: **Thu Oct 28, 2021 10:49 am**

Make sure to always change the GNSS option to external while compiling as you use external one.

Posted: **Thu Oct 28, 2021 10:52 am**

Please also change following line in FreematicsPlus.cpp (the library) so more information can be obtained. Tick "Rebuild libs" before compiling again.

Code: Select all

#define VERBOSE_XBEE 1

Freematics Forum

2x Freematics ONE+ Traccar Edition aren't working

2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working

Re: 2x Freematics ONE+ Traccar Edition aren't working